搜尋結果
- 39.05-0.15 (-0.38%)2024/10/14 06:30 臺灣股市 將在 2 小時 30 分鐘 期間開市 (報價延遲20分鐘)。
- 昨收39.20開盤39.30委買價0.00委賣價0.00
- 今日價格區間39.00 - 39.4552週價格區間35.25 - 46.90成交量524 張平均成交量899 張
- 市值7.790 億本益比 (最近12個月)14.00營運報告/法說會日期不適用除權除息日2024-07-26
相關股票
2008年2月1日 · Solved: Hi all, Recently I got a job in a new Company where they use 6509 Switches. Really I am facing some problems that most of the commands that I was using in 4506 Switch is not working here. I can't even see the status of a particular port. Can
2011年11月22日 · You need mimimum of 2500W powers per power supply. You set up is not supported. Also, I don't see what FAN module is in the chassis, I am hoping you are using FAN2 if it is not a E chassis.
2009年6月10日 · The Cisco Catalyst 6509-E supports both Cisco Catalyst OS and Cisco IOS Software. It also supports up to an 8700W power supply, thus providing the ability to support large numbers of IEEE 802.3af PoE devices. The Cisco Catalyst 6509-E provides maximum uptime with redundancy and rapid (1 to 3 seconds) stateful failover across supervisor engines.
2014年8月18日 · Solved: We have a single 6509 and a pair of 6509's in a VSS config. We want to be able to monitor all the device modules using snmp. On the single 6509 we can grab the moduleModel (17) and moduleStatus (10) using OIDs .1.3.6.1.4.1.9.5.1.3.1.1.17
2008年1月4日 · After an overheating environmental event, our 6509 boots into rommon. At the rommon prompt we can manually boot from the image on disk1. The boot variable is set to boot from the image on disk1, and the config register is 0x2102. But on reload or power up the sup comes up in rommon. Chassis is cisco WS-C6509-E with Sup720, image is IOS (tm ...
2013年7月3日 · The 6509-E is 80 Gbps/slot capable and can support the WS-X67xx Fabric. linecards while the 6500 can't. While those are the 2 big differences, this document is the best one. I've found that shows the differences: Cisco Catalyst 6500 and 6500-E Series Switch Data Sheet.
2013年5月2日 · 1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E") 2. inserting the line-cards exactly in the same slots and connecting all cables. 3. switch on the new chassis, witing to come up in VSS.
2003年4月3日 · Assuming your running CatOS on your 6509. If so then the "show cam" command will show you the mac to port table that the "show mac" command does on your 35xx switches. If you are running Natvie IOS on your 6509 "show mac" is the command you need. Run the "show cam dynamic" command on the supervisor. Regards, Don. View solution in original post.
2018年8月27日 · Hi. We are looking at a core upgrade over the next 12 months, currently we have a 6509 with mix of 48 port rj45, SFP gigabit modules as well as a 12 port 10gig module in each. I am not sure about the 6800 as I hear it has not taken off that well etc. The Nexus is just too much to invest as we dont require high throughput etc.
2019年3月7日 · Solved: Hello I believe I have a faulty module on a cisco 6509 I would like to confirm the troubleshooting process / commands for checking / re-seating the faulty module. Will physically re-seating the module help "flapping" issues I have been having with the ports on the module i.e. the ports are constantly showing going up and down.